Ik ga weer eens een clean install doenquote:Op zaterdag 18 april 2009 11:38 schreef Farenji het volgende:
Ik gebruik nog gewoon ext3, heb een upgrade vanuit 8.10 gedaan en ik heb geen zin om eerst alles te moeten backuppen. Ja ik weet dat je ext3 gewoon kan converteren maar dat ga ik niet zonder backup doen.
herkenbaar. ik heb ook altijd het idee dat mijn pc ineens veel beter werktquote:Op zaterdag 18 april 2009 11:47 schreef PiRANiA het volgende:
[..]
Ik ga weer eens een clean install doen
Geeft altijd een lekker gevoel om met een schoon sys te beginnen
Tis toch veel leuker om een oude release goed te onderhouden en geen clean install te hoeven doenquote:Op zaterdag 18 april 2009 11:47 schreef PiRANiA het volgende:
[..]
Ik ga weer eens een clean install doen
Geeft altijd een lekker gevoel om met een schoon sys te beginnen
lsb_release -aquote:Op zaterdag 18 april 2009 15:40 schreef northernlight81 het volgende:
Hoe kun je zien of je geupdate bent naar de RC?, en dus ook of je volgende wee de final hebt?
Als je 9.04 geinstalleerd hebt en je kwa updates up-to-date bent, dan zit je automatisch op de laatste release. Er is niet iets van een patch oid, het is gewoon updates onderhouden.quote:Op zaterdag 18 april 2009 15:40 schreef northernlight81 het volgende:
Hoe kun je zien of je geupdate bent naar de RC?, en dus ook of je volgende wee de final hebt?
minder accu verbruik........quote:Op zondag 19 april 2009 12:25 schreef wdn het volgende:
Iemand anders ook last van een wit scherm tijdens het rebooten/shutdownen?
Smplayer springt in 'pauze' als de kabel eruit gaat of in gaat. dat vind ik nogal irritant.
Iemand een idee waar dat aan kan liggen?
Opvallend: mijn batterijtijd is naar 4h25 gegaan. Onder 8.10 was dat 4h.
Nee alleen veranderd hij wel overdreven vaak van resolutie hier bij opstarten 5 keer en afsluiten 2 keer. Vind ik best wel irri voor mijn oude crt die er aanhangt.quote:Op zondag 19 april 2009 12:25 schreef wdn het volgende:
Iemand anders ook last van een wit scherm tijdens het rebooten/shutdownen?
Smplayer springt in 'pauze' als de kabel eruit gaat of in gaat. dat vind ik nogal irritant.
Iemand een idee waar dat aan kan liggen?
Opvallend: mijn batterijtijd is naar 4h25 gegaan. Onder 8.10 was dat 4h.
Briljante conclusiequote:
1 |
quote:Xrandr is used to set the size, orientation and/or reflection of the
outputs for a screen. It can also set the screen size.
If invoked without any option, it will dump the state of the outputs,
showing the existing modes for each of them, with a ’+’ after the pre‐
ferred mode and a ’*’ after the current mode.
There are a few global options. Other options modify the last output
that is specified in earlier parameters in the command line. Multiple
outputs may be modified at the same time by passing multiple --output
options followed immediately by their corresponding modifying options.
Ik krijg unknown bij detect displays en kon geen hogere resolutie kiezen. Dat nvidia programma is hetzelfde.quote:Op zondag 19 april 2009 19:58 schreef wdn het volgende:
Voor de scherm resolutie kennen we het commando:
[ code verwijderd ]
[..]
[ afbeelding ]
Wat krijg jij hier te zien?
(Wat doet de knop "detect displays"?)
En met dit:quote:
1 |
1 |
1 2 | sudo aticonfig --overlay-type=Xv |
quote:Latest ATI Linux Driver Introduces Support for Ubuntu 9.04
Yet another stable version of the ATI/AMD Linux display driver was released last night, for both x86 and x86_64 architectures. With version 9.4, ATI Catalyst introduces early support for the upcoming Ubuntu 9.04 operating system and full support for the recently released Red Hat Enterprise Linux 5.3. Users of the Release Candidate of Ubuntu 9.04 (Jaunty Jackalope) can install and test this new ATI driver via the "Hardware Drivers" utility in the System -> Administration menu. Without further introduction, we invite you to take a look at the resolved issues of the new ATI Catalyst 9.4 video driver from AMD: https://a248.e.akamai.net(...)linux_cat92-inst.pdf
Requirements:
· X.Org 6.8, 6.9, 7.0, 7.1, 7.2, 7.3 or 7.4
· Linux kernel 2.6 or higher
· glibc version 2.2 or 2.3
· Support for POSIX Shared Memory (/dev/shm) is necessary for 3D programs
· The following packages should be installed on your system: XFree86-Mesa-libGL, libstdc++, libgcc, XFree86-libs, fontconfig, freetype and zlib.
Supported operating systems:
· Red Hat Enterprise Linux
· Novell SUSE Enterprise Linux
· Ubuntu Linux
|
Forum Opties | |
---|---|
Forumhop: | |
Hop naar: |